Sun Fire X2. 20. 0 M2 Server Overview. Sun Fire X2. 20. 0 M2 Server Overview. This chapter provides an overview of the Sun Fire X2. Steps for accessing serial console of Sun ALOM, ILOM, ELOM and v20z/v40z systems. To exit the serial console. Accessing Serial console of ELOM systems (specific ones like Sun Fire X2100, X2100 M2, X2200, X2200 M2). Start > Sun > X2200-M2 > LOM. Last edited by dave, 6 years and 34 days ago. You can make the LOM do a DHCP request manually by connecting to the serial port, logging in, and issuing the command. Download the latest drivers for your Sun Microsystems Sun Fire X2200 M2 to keep your Computer up-to-date. SUN FIRE X2270 M2 SERVER FEATURES xCompact 1RU entry level server xPowered by Intel Xeon Processor 5600 Series xSupports up to 12 DIMMs, with maximum memory of 96 GB. SunFire X2200 - Debian Squeeze Installation via eLOM. This document is an attempt at step-by-step instructions for installing Debian Squeeze on a Sun SunFire X2200 using the eLOM management. Configure the serial port. Sun Fire X2200 M2 Server. Server 2.2.1 download (22-Apr-2010) SP 3.23. Sun Server X2-8 (formerly Sun Fire X4800 M2 Server) ILOM 3.2.6.22.a r110612 BIOS vers. Server 1.4.1 download. Dear managers, since I did not get the serial port on the backplane of the X2200 to work I am now trying to make use of a USA-19QW KeySpan USB-To-Serial adaptor. Setting Up the Sun Fire X2200 M2 Server Software This chapter. M2 server, as well as power- on and power- off procedures and information about installing components. TABLE 1- 1 Sun Fire X2. M2 Server Features Component. Two dual- core or quad- core AMD Opteron CPUs. Processor frequencies: 1. GHz and faster. Up to 1 MB level 2 cache. Eight DIMM slots per CPU socket. Each DIMM socket on board supports 1 GB or 2 GB registered buffered DDR2 DIMM modules. See the Embedded Lights Out Manager Administration Guide for more information on system management. Connect grounded AC power cords to the AC power connector on the back panel of the server and to a grounded AC power outlet. You can proceed to Chapter 2 of this guide to begin initial configuration. Do not apply main power to the rest of the server until you are ready to install a platform operating system. Continue with initial software setup tasks, as described in Sun Fire X2. How to start up console on Sun Fire X2200 ILOM using SSH? If your OS is booted to a graphical login screen, then there is no output to the serial console. You should check the graphical redirection from the ELOM web gui.M2 Server Installation Guide. Verify that the power cord has been connected and that standby power is on. This causes Advanced Configuration and Power Interface (ACPI) enabled operating systems to perform an orderly shutdown of the operating system. Servers not running ACPI- enabled operating systems will shut down to standby power mode immediately. When the main power is off, the Power/OK LED on the front panel will begin flashing, indicating that the server is in standby power mode. For example, if the server hangs because of incorrect settings and will not boot, use this procedure to invalidate the settings and reboot with the default settings. Remove the AC power cord. Remove the server’s top cover. Remove the system battery by pulling it up and out of the holder (see FIGURE 1- 4). To clear CMOS, you must make the metal clip and the contact point in the battery holder touch (short) for a period of 6. Press the metal clip on the battery holder inward until it touches (shorts) the metal contact point in the base of the battery holder (see. FIGURE 1- 4). Continue shorting the clip and the contact point for a period of 6. After 6. 0 seconds, install the battery, making certain that the positive (. Install the air duct, and secure it with the air duct retaining screw. Reinsert the AC power cord. For the most up- to- date component information, see the components list on one of the following web sites. How to start up console on Sun Fire X2. ILOM using SSH? How & where to check the graphical redirection from the ELOM web gui. Any documentation/command to try out? There was a brief moment where it was possible to see the hardware initialization together with boot up from Solaris 1. DVD lines after powercycle before returning to freezing the whole screen again. It almost appears as though I need to set terminal emulation on Putty to run in possibly vt. ANSI. Note that this server in single- user mode boot up from Solaris 1. DVD disk, has not been configured with a network connection. Hence, a Putty SSH brings me to ELOM prompt. On the other hand, I can SSH to the console on an identical system in multi- user mode on the network. Not sure whether this difference may have anything to do with the current issue. Thanks a lot again,George.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2017
Categories |